ABB RDNA-01 Manuel d'utilisateur Page 135
- Page / 348
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
ACH550-UH User’s Manual 1-131
Parameters
3010 STALL FUNCTION 0…2 1 0 (NOT SEL)
This parameter defines the operation of the Stall function. This
protection is active if the drive operates in the stall region (see the
figure) for the time defined by 3012
STALL TIME. The “User Limit” is
defined in Group 20: LIMITS by 2017
MAX TORQUE 1, 2018 MAX TORQUE
2, or the limit on the
COMM input.
0 =
NOT SEL – Stall protection is not used.
1 =
FAULT – When the drive operates in the stall region for the time set
by 3012
STALL TIME:
• The drive coasts to stop.
• A fault indication is displayed.
2 =
ALARM – When the drive operates in the stall region for the time set
by 3012
STALL TIME:
• An alarm indication is displayed.
• The alarm disappears when the drive is out of the stall region for
half the time set by parameter 3012
STALL TIME.
3011 STALL FREQUENCY 0.5…50.0 Hz 0.1 Hz 20.0 Hz
This parameter sets the frequency value for the Stall function. See parameter 3010.
3012 STALL TIME 10…400 s 1 s 20 s
This parameter sets the time value for the Stall function.
3017 EARTH FAULT 0, 1 1 1 (
ENABLE)
Defines the drive response if the drive detects a ground fault in the motor or motor cables. The drive monitors for
ground faults while the drive is running, and while the drive is not running. Also see parameter 3023
WIRING FAULT.
0 =
DISABLE – No drive response to ground faults.
Note: Disabling earth fault (ground fault) may void the warranty.
1 =
ENABLE – Ground faults display fault 16 (EARTH FAULT), and (if running) the drive coasts to stop.
3018 COMM FAULT FUNC 0…3 1 0 (NOT SEL)
Defines the drive response if the fieldbus communication is lost.
0 =
NOT SEL – No response.
1 =
FAULT – Displays a fault (28, SERIAL 1 ERR) and the drive coasts to stop.
2 = CONST SP 7 – Displays an alarm (2005, I/O COMM) and sets speed using 1208 CONST SPEED 7. This “alarm speed”
remains active until the fieldbus writes a new reference value.
3 =
LAST SPEED – Displays an alarm (2005, I/O COMM) and sets speed using the last operating level. This value is the
average speed over the last 10 seconds. This “alarm speed” remains active until the fieldbus writes a new
reference value.
WARNING! If you select
CONST SP 7, or LAST SPEED, make sure that continued operation is safe when
fieldbus communication is lost.
3019 COMM FAULT TIME 0.0…600.0 s 0.1 s 10.0 s
Sets the communication fault time used with 3018
COMM FAULT FUNC.
• Brief interruptions in the fieldbus communication are not treated as faults if they are less than the
COMM FAULT TIME
value.
3021 AI1 FAULT LIMIT 0.0…100.0% 0.1% 0.0%
Sets a fault level for analog input 1.
• See 3001
AI<MIN FUNCTION.
3022 AI2 FAULT LIMIT 0.0…100.0% 0.1% 0.0%
Sets a fault level for analog input 2.
• See 3001
AI<MIN FUNCTION.
Group 30: Fault Functions
Code Description Range Resolution Default S
95%
limit
User
Stall region
Torque/
Current
f
Stall frequency
P 3011
- …550 HP) 1
- …400 HP) 1
- List of related manuals 2
- Manual contents 3
- ACH550-UH HVAC Drives 5
- 1…550 HP 5
- User’s Manual 5
- Use of warnings and notes 7
- 1-4 ACH550-UH User’s Manual 8
- 1-6 ACH550-UH User’s Manual 10
- Table of contents 10
- ACH550-UH User’s Manual 1-7 11
- 1-8 ACH550-UH User’s Manual 12
- Installation 13
- Preparing for installation 14
- ACH550-UH User’s Manual 1-11 15
- ACH550-UH-08A8-4+ 15
- 1-12 ACH550-UH User’s Manual 16
- Installing the drive 17
- 1-14 ACH550-UH User’s Manual 18
- ACH550-UH User’s Manual 1-15 19
- 1-16 ACH550-UH User’s Manual 20
- ACH550-UH User’s Manual 1-17 21
- 1-18 ACH550-UH User’s Manual 22
- ACH550-UH User’s Manual 1-19 23
- 1-20 ACH550-UH User’s Manual 24
- R5 and R6 25
- 1-22 ACH550-UH User’s Manual 26
- ACH550-UH User’s Manual 1-23 27
- 1-24 ACH550-UH User’s Manual 28
- ACH550-UH User’s Manual 1-25 29
- 1-26 ACH550-UH User’s Manual 30
- ACH550-UH User’s Manual 1-27 31
- 1-28 ACH550-UH User’s Manual 32
- ACH550-UH User’s Manual 1-29 33
- 1-30 ACH550-UH User’s Manual 34
- ACH550-UH User’s Manual 1-31 35
- 1-32 ACH550-UH User’s Manual 36
- HVAC control panel modes 38
- ACH550-UH User’s Manual 1-35 39
- 1-36 ACH550-UH User’s Manual 40
- ACH550-UH User’s Manual 1-37 41
- Changed Parameters Mode 42
- ACH550-UH User’s Manual 1-39 43
- 1-42 ACH550-UH User’s Manual 46
- ACH550-UH User’s Manual 1-43 47
- 1-44 ACH550-UH User’s Manual 48
- ACH550-UH User’s Manual 1-45 49
- I/O Settings Mode 50
- Start-up 51
- 1-48 ACH550-UH User’s Manual 52
- Application macros 53
- 1-50 ACH550-UH User’s Manual 54
- HVAC Default macro 55
- Supply Fan macro 56
- Return Fan macro 57
- Cooling Tower Fan macro 58
- Condenser macro 59
- Booster Pump macro 60
- Pump Alternation macro 61
- Internal Timer macro 62
- ACH550-UH User’s Manual 1-59 63
- Floating Point macro 64
- Dual Setpoint with PID macro 65
- 1-62 ACH550-UH User’s Manual 66
- E-bypass macro 67
- Hand Control macro 68
- E-Clipse macro 69
- 1-66 ACH550-UH User’s Manual 70
- 1-68 ACH550-UH User’s Manual 72
- ACH550-UH User’s Manual 1-69 73
- 1-70 ACH550-UH User’s Manual 74
- ACH550-UH User’s Manual 1-71 75
- 1-72 ACH550-UH User’s Manual 76
- ACH550-UH User’s Manual 1-73 77
- 1-74 ACH550-UH User’s Manual 78
- ACH550-UH User’s Manual 1-75 79
- 1-76 ACH550-UH User’s Manual 80
- ACH550-UH User’s Manual 1-77 81
- 1-78 ACH550-UH User’s Manual 82
- ACH550-UH User’s Manual 1-79 83
- 1-80 ACH550-UH User’s Manual 84
- ACH550-UH User’s Manual 1-81 85
- Group 01: OPERATING DATA 86
- ACH550-UH User’s Manual 1-83 87
- 1-84 ACH550-UH User’s Manual 88
- ACH550-UH User’s Manual 1-85 89
- 1-86 ACH550-UH User’s Manual 90
- Group 03: ACTUAL SIGNALS 91
- 1-88 ACH550-UH User’s Manual 92
- ACH550-UH User’s Manual 1-89 93
- 1-90 ACH550-UH User’s Manual 94
- Group 04: FAULT HISTORY 95
- 1-92 ACH550-UH User’s Manual 96
- ACH550-UH User’s Manual 1-93 97
- Group 11: REFERENCE SELECT 98
- This group defines: 98
- 1 and REF2 98
- ACH550-UH User’s Manual 1-95 99
- 1-96 ACH550-UH User’s Manual 100
- Parameters 100
- ACH550-UH User’s Manual 1-97 101
- 1-98 ACH550-UH User’s Manual 102
- ACH550-UH User’s Manual 1-99 103
- 1-100 ACH550-UH User’s Manual 104
- ACH550-UH User’s Manual 1-101 105
- Group 13: ANALOG INPUTS 106
- Group 14: RELAY OUTPUTS 107
- 1-104 ACH550-UH User’s Manual 108
- ACH550-UH User’s Manual 1-105 109
- 1-106 ACH550-UH User’s Manual 110
- ACH550-UH User’s Manual 1-107 111
- Group 16: SYSTEM CONTROLS 112
- ACH550-UH User’s Manual 1-109 113
- 1-110 ACH550-UH User’s Manual 114
- ACH550-UH User’s Manual 1-111 115
- 1-112 ACH550-UH User’s Manual 116
- ACH550-UH User’s Manual 1-113 117
- 1-114 ACH550-UH User’s Manual 118
- Group 20: LIMITS 119
- 1-116 ACH550-UH User’s Manual 120
- ACH550-UH User’s Manual 1-117 121
- Group 21: START/STOP 122
- ACH550-UH User’s Manual 1-119 123
- 1-120 ACH550-UH User’s Manual 124
- Group 22: ACCEL/DECEL 125
- 1-122 ACH550-UH User’s Manual 126
- Group 23: SPEED CONTROL 127
- 1-124 ACH550-UH User’s Manual 128
- 0, 1 1 0 (OFF) 129
- Group 26: MOTOR CONTROL 130
- ACH550-UH User’s Manual 1-127 131
- Group 29: MAINTENANCE TRIG 132
- Group 30: FAULT FUNCTIONS 133
- 1-130 ACH550-UH User’s Manual 134
- ACH550-UH User’s Manual 1-131 135
- 1-132 ACH550-UH User’s Manual 136
- Group 31: AUTOMATIC RESET 137
- 1-134 ACH550-UH User’s Manual 138
- Group 32: SUPERVISION 139
- 1-136 ACH550-UH User’s Manual 140
- Group 33: INFORMATION 141
- Group 34: PANEL DISPLAY 142
- ACH550-UH User’s Manual 1-139 143
- 1-140 ACH550-UH User’s Manual 144
- ACH550-UH User’s Manual 1-141 145
- FAULT FUNCTIONS 146
- ACH550-UH User’s Manual 1-143 147
- 1-144 ACH550-UH User’s Manual 148
- ACH550-UH User’s Manual 1-145 149
- 1-146 ACH550-UH User’s Manual 150
- ACH550-UH User’s Manual 1-147 151
- Group 37: USER LOAD CURVE 152
- ACH550-UH User’s Manual 1-149 153
- 1-150 ACH550-UH User’s Manual 154
- ACH550-UH User’s Manual 1-151 155
- 1-152 ACH550-UH User’s Manual 156
- ACH550-UH User’s Manual 1-153 157
- 1-154 ACH550-UH User’s Manual 158
- ACH550-UH User’s Manual 1-155 159
- 1-156 ACH550-UH User’s Manual 160
- ACH550-UH User’s Manual 1-157 161
- 1-158 ACH550-UH User’s Manual 162
- ACH550-UH User’s Manual 1-159 163
- Group 41: PROCESS PID SET 2 164
- 1 PARAM SET 164
- ACH550-UH User’s Manual 1-161 165
- 1-162 ACH550-UH User’s Manual 166
- ACH550-UH User’s Manual 1-163 167
- Group 51: EXT COMM MODULE 168
- ACH550-UH User’s Manual 1-165 169
- Group 52: PANEL COMM 170
- Group 53: EFB PROTOCOL 171
- 1-168 ACH550-UH User’s Manual 172
- ACH550-UH User’s Manual 1-169 173
- 1-170 ACH550-UH User’s Manual 174
- ACH550-UH User’s Manual 1-171 175
- 1-172 ACH550-UH User’s Manual 176
- ACH550-UH User’s Manual 1-173 177
- 1-174 ACH550-UH User’s Manual 178
- ACH550-UH User’s Manual 1-175 179
- 1-176 ACH550-UH User’s Manual 180
- ACH550-UH User’s Manual 1-177 181
- 1-178 ACH550-UH User’s Manual 182
- ACH550-UH User’s Manual 1-179 183
- 1-180 ACH550-UH User’s Manual 184
- ACH550-UH User’s Manual 1-181 185
- 1-182 ACH550-UH User’s Manual 186
- ACH550-UH User’s Manual 1-183 187
- 1-184 ACH550-UH User’s Manual 188
- Group 98: OPTIONS 189
- 1-186 ACH550-UH User’s Manual 190
- Embedded fieldbus 191
- 1-188 ACH550-UH User’s Manual 192
- ACH550-UH User’s Manual 1-189 193
- Preferred wiring diagram 194
- Alternate wiring diagram 194
- Communication setup – EFB 195
- 1-192 ACH550-UH User’s Manual 196
- ACH550-UH User’s Manual 1-193 197
- Service 198
- ACH550-UH User’s Manual 1-195 199
- 1-196 ACH550-UH User’s Manual 200
- Miscellaneous driv e control 201
- 1-198 ACH550-UH User’s Manual 202
- ACH550-UH User’s Manual 1-199 203
- Feedback from the drive – EFB 204
- ACH550-UH User’s Manual 1-201 205
- Diagnostics – EFB 206
- ACH550-UH User’s Manual 1-203 207
- 1-204 ACH550-UH User’s Manual 208
- ACH550-UH User’s Manual 1-205 209
- 1-206 ACH550-UH User’s Manual 210
- N2 protocol technical data 211
- 1-208 ACH550-UH User’s Manual 212
- PC-Version 213
- Converter 213
- Panel Version/LTD 213
- N2 binary input objects 214
- N2 analog output objects 215
- FLN protocol technical data 219
- Overview 220
- Drive I/O 221
- Drive Config 221
- Process PID 222
- External PID 222
- ACH550-UH User’s Manual 1-219 223
- ° F - 30° F) x (0.1) 223
- ° F - 30° F) x (0.01) 223
- Point database 224
- ACH550-UH User’s Manual 1-221 225
- 1-222 ACH550-UH User’s Manual 226
- Detailed point descriptions 227
- 1-224 ACH550-UH User’s Manual 228
- ACH550-UH User’s Manual 1-225 229
- 1-226 ACH550-UH User’s Manual 230
- ACH550-UH User’s Manual 1-227 231
- 1-228 ACH550-UH User’s Manual 232
- ACH550-UH User’s Manual 1-229 233
- 1-230 ACH550-UH User’s Manual 234
- ACH550-UH User’s Manual 1-231 235
- 1-232 ACH550-UH User’s Manual 236
- ACH550-UH User’s Manual 1-233 237
- 1-234 ACH550-UH User’s Manual 238
- ACH550-UH User’s Manual 1-235 239
- 1-236 ACH550-UH User’s Manual 240
- ACH550-UH User’s Manual 1-237 241
- Statement 242
- ACH550-UH User’s Manual 1-239 243
- BACnet Object Definitions 244
- ACH550-UH User’s Manual 1-241 245
- 1-242 ACH550-UH User’s Manual 246
- For the 0xxxx registers: 247
- • Status is always readable 247
- 1-244 ACH550-UH User’s Manual 248
- ACH550-UH User’s Manual 1-245 249
- 1-246 ACH550-UH User’s Manual 250
- ACH550-UH User’s Manual 1-247 251
- 1-248 ACH550-UH User’s Manual 252
- ACH550-UH User’s Manual 1-249 253
- ABB drives profile 254
- DCU profile 255
- Status Word 256
- The contents of the 256
- ACH550-UH User’s Manual 1-255 259
- 1-256 ACH550-UH User’s Manual 260
- ACH550-UH User’s Manual 1-257 261
- 1-258 ACH550-UH User’s Manual 262
- ACH550-UH User’s Manual 1-259 263
- 1-260 ACH550-UH User’s Manual 264
- Fieldbus adapter 265
- 1-262 ACH550-UH User’s Manual 266
- ACH550-UH User’s Manual 1-263 267
- Communication setup – FBA 269
- 1-266 ACH550-UH User’s Manual 270
- ACH550-UH User’s Manual 1-267 271
- Feedback from the drive – FBA 272
- Diagnostics – FBA 273
- 1-270 ACH550-UH User’s Manual 274
- ACH550-UH User’s Manual 1-271 275
- 1-272 ACH550-UH User’s Manual 276
- WORD is status 277
- WORD (SW) bits 278
- ACH550-UH User’s Manual 1-275 279
- 1-276 ACH550-UH User’s Manual 280
- ACH550-UH User’s Manual 1-277 281
- 1-278 ACH550-UH User’s Manual 282
- ACH550-UH User’s Manual 1-279 283
- 1-280 ACH550-UH User’s Manual 284
- Diagnostics 285
- Correcting faults 286
- ACH550-UH User’s Manual 1-283 287
- 1-284 ACH550-UH User’s Manual 288
- ACH550-UH User’s Manual 1-285 289
- 1-286 ACH550-UH User’s Manual 290
- ACH550-UH User’s Manual 1-287 291
- Correcting alarms 292
- ACH550-UH User’s Manual 1-289 293
- 1-290 ACH550-UH User’s Manual 294
- Maintenance 295
- Drive module fan replacement 296
- ACH550-UH User’s Manual 1-293 297
- 1-294 ACH550-UH User’s Manual 298
- ACH550-UH User’s Manual 1-295 299
- 1-296 ACH550-UH User’s Manual 300
- ACH550-UH User’s Manual 1-297 301
- Capacitors 302
- Control panel 302
- Technical data 303
- Ratings, 380…480 volt drives 304
- 1-302 ACH550-UH User’s Manual 306
- Input power connections 307
- 208…240 volt, fuses 308
- 380…480 volt, fuses 308
- ACH550-UH User’s Manual 1-305 309
- 1-306 ACH550-UH User’s Manual 310
- ACH550-UH User’s Manual 1-307 311
- 1-308 ACH550-UH User’s Manual 312
- ACH550-UH User’s Manual 1-309 313
- 1-310 ACH550-UH User’s Manual 314
- Motor connections 315
- 1-312 ACH550-UH User’s Manual 316
- ACH550-UH User’s Manual 1-313 317
- 1-314 ACH550-UH User’s Manual 318
- ACH550-UH User’s Manual 1-315 319
- 1-316 ACH550-UH User’s Manual 320
- Control connections 321
- 1-318 ACH550-UH User’s Manual 322
- ACH550-UH User’s Manual 1-319 323
- Efficiency 324
- Air flow, 380…480 volt drives 325
- Dimensions and weights 326
- Mounting dimensions 327
- R1…R6 mounting dimensions 327
- 1-324 ACH550-UH User’s Manual 328
- Outside dimensions – R1…R6 329
- 1-326 ACH550-UH User’s Manual 330
- Degrees of protection 331
- Ambient conditions 332
- Materials 333
- Applicable standards 334
- ACH550-UH User’s Manual 1-331 335
- Liability limits 336
- ACH550-UH User’s Manual 1-333 337
- Numerics 338
Produits connexes et manuels pour Non ABB RDNA-01
Non ABB Tina 7A Manuel de service
(12 pages)
(12 pages)
Non ABB FENA-01 Manuel d'utilisateur
(34 pages)
(34 pages)
Non ABB FPBA-01 Spécifications
(21 pages)
(21 pages)
Non ABB FENA-21 Manuel d'utilisateur
(46 pages)
(46 pages)
Non ABB RECA-01 Manuel d'utilisateur
(6 pages)
(6 pages)
Non ABB FDNA-01 Manuel d'utilisateur
(460 pages)
(460 pages)
Non ABB RDNA-01 Manuel d'utilisateur
(330 pages)
(330 pages)
Non ABB Tina 7A Manuel de service
(62 pages)
(62 pages)
Non ABB RDNA-01 Manuel d'utilisateur
(302 pages)
(302 pages)
Non ABB Tina 7A Manuel d'utilisateur
(44 pages)
(44 pages)
Non ABB ML82PH Manuel d'utilisateur
(29 pages)
(29 pages)
© 2020, manymanuals.fr. Tous droits réservés | 5.829 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels